How to Replace the Replacement Key Battery For the Saab 9-3

Saab owners have a distinct set of steps to add a second key. This requires the use of a handheld computer, known as Tech-2 which is used by the dealer. Then the transponder is replaced and a key are required to be purchased.

Change your keys regularly to prevent one from deteriorating faster than the other. This will keep your keys in good condition.

Replacement Case

The new key fobs are not like the old Saab keys. They are equipped with electronics that make it difficult to duplicate. This has made theft of cars much more difficult than it was a few years ago. However, it has made replacing lost keys an incredibly expensive endeavor.

Every owner of a 9-3 Saab should have at least two working keys. If one gets lost, it costs a lot to purchase a new one for the car since it requires replacing the CIM module and programming the locking cylinders. Dealers charge between $100 and $200 for this.

There are ways to cut down on these costs. Certain parts suppliers will utilize the code of an extra key to cut a brand new metal blade for less than that of a dealer. The key must be the exact same as the original in order for it to function in your vehicle.

Follow these steps to replace the case. You will need a flathead screwdriver as well as some patience. With the screwdriver, break off the plastic and then remove the emergency key. When the case is opened take the electronics out and put them in your new case. Be sure to put the correct key and badge back inside the case, too.

Replacement Battery

The saab 9-3 key replacement (view yogaasanas.science) 9-3 replacement key for saab 93 battery is an inexpensive component that can be easily and quickly replaced. This YouTube video from Cyclone Cyd demonstrates how to replace the battery for the remote fob in just four steps. This tutorial is compatible with any modern Saab key fob. However, the process might differ slightly.

The first step is to locate the button that releases the backup key on the fob. The button is usually found on the back of your fob, close to the Saab Logo. Then, use a flathead screwdriver into the small hole inside this button. This should be sufficient to open the fob case to allow you to change the battery.

After the new battery CR1632 is installed, you can reassemble the remote key fob. You can then program it to your car. The entire process shouldn't exceed an hour. It is a simple procedure that doesn't require any special tools.

The process can be a bit more complicated in the event that you lose your key, but it is possible. The dealer needs to first determine the VIN of the vehicle, and then purchase a replacement TWICE module and key blade with the proper unique code. The dealer will then need to program the key using MDI, a brand new software tool.

Replacement Key Fob

The key fob is equipped with an internal battery that is used to lock and unlock your vehicle. The batteries last for a certain time and will eventually expire. This is a regular issue that affects all cars, and the good news is that you can change the batteries on most key fobs without replacing the entire case. You can buy fobs replacements on Amazon that have all the electronics already installed, so you can just pop open the case and replace the old batteries. It is important to note that you'll need to remove the emergency key first. you can do this by putting the screwdriver of a small flathead into the slot found in the middle of the case. The case will split once you work the screwdriver all around it.

If you're about to replace your keys, make sure you have a spare, because this can cut down the total cost by a significant amount. If you have a spare you can request that the dealer cut the new key and program it to your car, which is much cheaper than replacing the entire key fob.

If you don't have a spare car key, you can add an additional key to your car, however this will require a lot of research and effort. Adding a second key costs several hundred dollars and it also requires programming of the car's computer. This can be done by a professional, but it's an expensive option for most owners.

Replacement Ignition

Unlike the earlier saab car key automobiles, the new SAAB 9-3 models have an upgraded alarm system that is built around a coded key. This means that should you lose only one functioning key, getting another one could be very expensive since the car has to have a specific computer module fitted and must also be specifically programmed to accept a new key. Dealers can even charge hundreds of dollars to program an entirely new key, if they are unable to do it.

Dealers will charge you the highest price to replace your car computer (also known as the CIM or saab key replacement twice) when you lose the only working key. Instead, we can reprogram the EEPROM of your current car computer to prepare it for a replacement key, which will save you more than 50% of what you'd have to pay at a dealership.

If you have owned a SAAB 9-3 for quite a while, you know that the ignition keys are not very durable. If the ignition key you have isn't functioning properly, it is time to look into replacing it. They can become very sticky and the buttons have been known to fall off. Fortunately, replacing the ignition key isn't as difficult as it sounds, and it can be done in a short time with the appropriate tools.