How to Replace a Kia Sportage replacement kia key fob Key

For a number of Kia models the key comes with a built-in keyless entry system. The key can be compared to an remote control, and can be replaced with a fresh one from an Kia dealer or locksmith.

Key fobs can fail to function due to a number of reasons, including batteries that are dead, worn-out buttons signal interference or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key to function again.

How to replace the remote key or the smart key?

The battery in your Kia's intelligent key will eventually need be replaced, regardless of whether it is a remote key Fob replacement Kia as well as a push-to start key or a normal metal key that is not equipped with transponder. This is particularly true if your car displays a message telling you that the remote or smart keys are in poor condition.

It's a simple procedure. In order to replace the battery in the key fob, remove the mechanical key from the slit at the back of the key fob and pry open the cover. Inside the key fob will be tiny screws that hold the battery in the correct position. Take out the old battery by detaching the screw with a small screwdriver. Then, insert the new and close the slit in the key fob.

Once the key fob has an updated battery and you've tested it, press the locks and unlock buttons. You're good to go if the doors lock and unlock as expected. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you need to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a computer that is only available to the locksmith in the automotive or dealer. Other keys (non transponder metal keys), do not need programming. If you want to change the programming of your key, you'll need to write down the key code's number on the tag for the key code.

How do you replace a battery?

If your kia picanto key programming key fob is not responding when you press the lock or unlock button on the fob, it is a good indicator that the battery should be replaced. A battery that is not functioning properly could cause other issues such as the check engine light coming on or delayed engine cranking. Fortunately replacing the key fob battery is a simple DIY project that requires only a few tools.

Make sure that you shut off your vehicle and close all doors before you begin. Find the small, metal or plastic piece near the bottom of the key fob. Jiggle it until the key pops out. The key can be inserted into the driver door handle to unlock your car.

To replace the key fob's battery, remove the cover from the back and use a plastic pry bar tool to remove the latch that holds the black negative battery cable. Remove the old battery, and then align the new battery so that the "+" positive side is facing you and the "negative" negative side is facing towards the fob's metal electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid bending or damaging the contacts made of metal.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks up. You can then test the Kia's Key fob to ensure it's working as intended.

How do I replace a smart key

There is a possibility of having the standard keyfob or Smart Key, based on the model of 2013 kia optima key Sportage. The difference between the two is that the smart fob has an incredibly small key blade hidden within it, whereas the standard fob isn't equipped with. Both key fobs have an internal battery that will eventually require replacement. It is a simple process that takes less than two minutes.

Before you get started it is important to ensure that you are on a level surface with adequate lighting and that the Kia is off. Also, keep in mind that there are tiny pieces inside the fob that can fall out if not vigilant.

The first step is to find the small release button on the lower backside of the fob. It could be an oval silver button or a rectangular slot. After pressing this button mechanical key blade, it will pop out and you can then open the key fob.

After the key fob has been removed, you can remove the battery that was in it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. After you've finished, your key fob will allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How do I replace the mechanical key

The Kia key fob is an amazing convenience that allows us to lock and unlock our car at the click of one button. Like any other device that is used, the Kia key fob can have issues at times. Luckily, there are steps to take to resolve these issues and keep our key fobs in good condition for the long term.

A low or dead battery is one of the most common problems. This could cause the fob to cease working or stop working at times. If this is what you are experiencing you should replace the battery a new one.

If this isn't enough to solve the issue, you can use the flathead screwdriver that is standard to push the plastic casing of the fob open. Be careful not to scratch any internal components or scratch the plastic. Once the battery is removed, replace it with a brand new one.

After the new battery has been put installed, close and unlock the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to make sure it is working correctly. If the fob isn't working, contact an expert locksmith or dealer to help solve the issue. Make sure they cut you an emergency key that works across all door and trunk cylinders to prevent lockouts in the future.