Peugeot 208 Key Replacement

Peugeot 208 key replacement car key peugeot 207 should be left to professional auto locksmiths who have the right equipment and know-how. They can create and program keys quicker and more efficiently than a dealership.

A dead coin battery is most likely to blame the reason your key-fob stops locking or unlocking the doors. There are also other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking and will not allow you to start the engine. If this is the case, you'll have to make use of the backup starting procedure which is explained in the owner's manual for your vehicle.

The spark plugs can also be worn out. Spark plugs are what ignite the fuel to start the engine. However, they have a limited life span. They'll eventually fail if they aren't used frequently enough.

Luckily, there's an easy solution to this issue. Examine the voltage of your battery with a multimeter. If it is below 11.5 volts, then you need to replace it. If the battery has corroded it is crucial to clean its contacts. You can do this by lifting the rubber covers that protect the two terminals on the battery and using a wire brush to remove any corroded areas of the battery. You should then reconnect the cables that connect the positive and negative poles.

Water Damage

If your 208 won't turn on and the battery isn't flat then you should check whether the spark plugs are functioning. It could be that they are filthy and don't spark. This can be easily corrected by cleaning the spark plugs in the workshop.

Peugeot automobiles are equipped with a transponder that is compatible with the immobiliser. This ensures only the correct key can turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the proper signal to the vehicle.

This is a typical issue that is often caused by water damage. This is a common issue in more cold climates where the car is exposed to rain or snow. In this case, you need to contact a trusted locksmith who will have the tools and equipment required to modify the key. They also have the latest technological know-how and machinery required to create the Peugeot 208 smart key. The process shouldn't be more than 15 minutes.

Faulty Battery Contacts

Peugeot replaced the old transponder chips with a brand new model that is based on electronic components mounted on a circuit board. The new system is great when it's brand new, but the circuit boards wear out over time and cease to function properly.

This could prevent the immobiliser from working, so your vehicle won't be able to start. Contact a peugeot 208 key programming instructions specialist, or a locksmith, if this is the case.

A common issue occurs when the battery inside the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A car locksmith can replace the battery and cut a new blade for you, this is generally a quick fix.

Faulty Receiver Module

It could be that the receiver module is faulty if your Peugeot key fob doesn't work after being dropped on the floor, or exposed to a sudden storm or accidentally washed. The receiver is responsible for transmitting radio frequency signals to the onboard computer which controls the centralized locking system inside your Peugeot vehicle.

The rubber seals on the key fob keep water from getting to the electronic chip. However, prolonged exposure to water can penetrate these seals and damage the chip. Submerging the key fob into ocean water at the beach or throwing it into the water can be particularly damaging due to the high salt content.

If your peugeot 207 key fob not working spare key fob isn't working, you'll need to have the module replaced. This can only be done by a Peugeot 2008 key fob not working specialist or a professional auto locksmith. Peugeot keys, unlike other cars, are secured by an immobilizer system. This requires the proper codes to start the car. This is why you should only go with a knowledgeable Peugeot locksmith for the job of programming and creating the replacement.

Computers with faulty on-board computers

The on-board computer in your Peugeot is the one responsible for all of the systems in your car, ranging from airbags to power windows. If something is wrong with these systems, it will typically show a code that identifies the problem. This code will be stored within the system until the issue is fixed. This can often mean that the on-board computers to be replaced.

One of the main causes of the light turning on is loose or corroded connectors in the airbag sensor. It can be due to wear and tear, aging, or exposure to moisture and salt. This issue needs to be addressed as soon as you can, because an airbag that's malfunctioning could pose a risk in the event in the event of an accident.

If your Peugeot is showing a card that is not being detected error, then the key battery in the key fob may be dead or weak. This prevents the key fob from sending a signal to disable the standard immobilizer in your vehicle. Test this by pressing the unlock key on the fob's key, then trying to start your vehicle. If this fails then the battery in the key must be replaced.