How to Replace a Kia Sportage Replacement Key

For a variety of Kia models keys, there is a built-in keyless entry system. The key functions like a remote control and can be exchanged by a kia transponder key dealer.

Key fobs can stop working for a variety of reasons, such as an empty coin battery, worn buttons, signal interference, water damage and a damaged receiver module. Here are some helpful tips on how to get your Kia Sportage replacement key to work again.

how much is a kia key fob - browse around this web-site, do you replace a smartkey or remote key?

If your Kia is equipped with an intelligent key, remote key push to start key, or a standard non-transponder key made of metal, the battery in these keys will eventually require replacing. This is particularly relevant if your vehicle displays a message indicating that the smart or remote keys have low battery power.

This is a relatively easy process. In order to replace the battery of the key fob remove the mechanical key from the hole in the back of the key fob and remove the cover. A small screw will be found inside the key fob to keep the battery in place. Remove the old battery by removing the screw with a small screwdriver. Then insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock exactly as you expect, then you're good to go! You can now make use of the 2014 kia sportage key fob's hands-free lock/unlock feature when your fingers are cold or you need to run some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming done. This requires a special programming machine that only the dealer or locksmith has access to. Other keys (non transponder metal keys), do not need programming. If your keys need to be reprogrammed, you must know the key code number written on the tag that identifies the key and then record the number in a secure place.

How to replace the battery

If the Kia key fob doesn't respond to pressing the lock/unlock button, it is likely that the battery is not fully charged. A battery that is not functioning properly can cause other issues, such as the check engine light turning on or the engine not cranking correctly. Fortunately replacing the key fob battery is a fairly simple DIY project that requires just a few basic tools.

Before you begin the process, make sure that your vehicle is off and that all doors are closed. Find the small metal or a plastic piece that is located at the bottom of the key fob. Jiggle it until the metal key is released. This key can be put into the door's driver handle to unlock your car.

To replace the key fob battery, remove the cover from the back and use a plier bar tool to remove the latch that holds the black negative battery cable. Take the old battery out, and then place the new battery so that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position, avoiding excessive force to avoid damaging or bending the contacts on the metal.

Once the new battery has been installed after which you turn the key fob off and then on in the ignition until the door locks cycle. You can then test the kia key fob programming near me's key fob again to make sure it's working as intended.

How do I replace a smart keys

You can have an ordinary keyfob or Smart Key based on the model of kia key fob programming near me Sportage. The difference is that the smart key comes with the small blade of a key tucked inside it, while the standard fob does not. Both kinds of key fobs contain an internal battery which eventually needs to be replaced. This is a straightforward process that takes just two minutes.

Make sure to shut off your Kia and stand on a flat well-lit and well-lit area before you begin. Also, keep in mind that there are tiny parts inside the fob which could be snagged if not careful.

The first step is to find the small release button on the lower backside of the fob. It can be an oval silver button or a rectangular slot. When you press it button, the mechanical blade will come out and you can then open the key fob.

Once you have the key fob open, you can simply take off the old battery and replace it. The new battery is one called CR-2032 and can be bought on the internet or at your local auto parts shop. After installation you should be able to lock and unlock your vehicle using your key fob - even if the engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob is an excellent convenience that allows us to lock or unlock our car by simply pressing one button. Like any other device it is possible that the Kia key fob may have issues. There are steps that can be taken to solve these issues and ensure that our key fobs are in good condition over the long haul.

A dead or drained battery is one of the most frequently encountered issues. The fob could be able to stop working altogether or stop working at times. If this is the issue, replace the battery with a new one.

If this does not resolve the issue, use a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not to scratch any internal components or scratch the plastic. When the battery is open, carefully take off the battery that was removed and replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to confirm it's functioning properly. If the device isn't working, call an expert locksmith or dealer to help resolve the issue. Make sure they make you an emergency key that can work in all the trunk and door cylinders, to avoid lockouts again.