Replacement UPVC Door Handles

You can find the perfect handle for your door, whether replacing your handles or adding extra security. Upvc handles are simple to install and meet the required 92mm centres for multipoint locks.

The backplate fixing center and the dimensions of the lever/keyhole are the most important measurements. Compare these measurements with your existing measurements prior to making a purchase.

Lever/Pad

Lever pad door handles are made up of the lever handle on one side and a paddle-shaped handle on the other. These are designed for use with key wind locks. However they can be affixed to multipoint split spindle door locks.

Once you have selected the appropriate handle for the doors the finishes will be displayed in the drop-down list. Not all styles of handles are available in every finish though and it is recommended to check the technical drawings and sizes sections for the particular product you're looking for to ensure that you get the correct size and fitting.

When choosing new lever pad door window handles for wooden windows made of upvc, it is crucial to make sure that they correspond to the PZ (distance between the handle spindle and the center of the cylinder hole) of your existing multipoint locks, since they have to be in line for the doors to remain locked, either from the inside or the outside. The handles we offer are designed to work with the majority of standard cylinder locks, however it is advisable to double-check before purchasing.

You'll need to take off the handles on your current handle and remove the lock case if you are upgrading to dual spindle levers for your handle as this will require an additional split inline cylinder. They can be purchased separately and we offer the complete technical diagram for you to look at in the images for each product.

After you have removed the screws that are holding the handle on your door, it is a good idea to loosen them and inspect the mechanism to determine how it's performing. You may have to loosen the screws further when they aren't tight, and then you can remove the old spindle and handle and put in your new upvc door handle. Before putting the handle in place it is recommended to ensure that it is in the correct place. You can do this by placing your finger into the gap between the door frame and the door handle to make sure that it is level.

Lever/Lever

Lever door handles function as with a multi-point lock that utilizes an Euro cylinder and can be found on a majority of upvc double doors, aluminium doors, and some wooden doors. They are available in two types, with an interior lever and a paddle outside. Sprung - these include a spring cassette within the backplate that helps bring the handle lever to an upright position. Non-sprung: They do not include a mechanism that can spring the handle lever to a horizontal position.

To fix a door handle that is sagging, you will need to locate the detent access hole or pin, which is typically a small rectangle or round shape hole or protruding pin located on one side of the base plate. Once you've located it, you can loosen the set screw with a screwdriver and remove it to allow the lever and return it to the horizontal position.

Once the handle is positioned horizontally, you can put back the screws. Tighten them to ensure that the handle stays connected to the base plate. Consider applying a threadlocking solution to the screw threads in order to improve grip and prevent the threads from becoming loose over time.

Lever door handles that droop could be the result of various causes. The most common reason is that the fixings have been over tightened and are putting strain on the bearings of the lever, causing it to bind against the door face. It could also be due to the fact that the levers aren't being operated at a straight angle and this is causing compression of the latch mechanism, preventing it from fully springing back into operation.

The most common reason for a spring lever not operating properly is that the spring is not being in the proper position on the backplate. To check whether the handle is back to horizontal, simply move it.

If the door handles aren't tight, it is essential to spot the issue fast, as it could cause excessive wear on the screws and possibly to the window handle repairs falling off the base plate. You should also tighten loose screws frequently to prevent them from becoming looser.

Lever/Snib

These handles made of upvc are also referred to as 'Snib' handle sets and have a snib lever at the top of the lever that can be pressed down to lock your door if you don't use the fake lock. They are typically fitted with a Fullex 68PZ (that's 68mm between the spindle's center and lever or lock centre) door lock. We also carry a selection of other door handles with 68PZ from various manufacturers, including Ferco and Fab & Fix.

Change your door handle is a cheap method to upgrade your home, regardless of whether you're replacing existing handles or fitting new ones on doors you've constructed in your home. There are various styles available for upvc door handles, including the traditional levers on backplates. Other options include curved or straight short latches as well as Dummy knobs for multi-point locks. These are great for French doors.

Lever on backplate handles are usually rectangular, but there are also circular or oval shaped models that are referred to as rose door handles. These types of door handles are equipped with an a knob or lever on a backplate that sits behind the lever or knob and is often referred to as the rosette, however some backplates can be removed to allow for concealed fixing.

These handles are available in various finishes, including chrome and coloured finishes to complement your door and other hardware such as knobs, bolts and hinges. Some handles are supplied with grub screws to aid in the secure attachment of the knob or lever to the spindle. Other handles come with bathroom spindles that can be used to control bathroom locks and include a thumbturn turn and release mechanism, ideal to use on doors for bathrooms.

Mortise

The tubular latch is the most likely to be the cause in the event that your door handle is slammed shut. It could be due to a number of things but the most prevalent is the lack of lubrication on the latch plate. This can be fixed quite easily by simply opening the door and spraying lubricant over the lock and handle. It could also be that the latch has come loose from the backplate. This could be more problematic and would require a professional to fix it.

A multipoint handle system is the best solution for a stuck door handle. These handles are mounted on the door's faceplate and are operated by an actuated thumb turn knob or key that triggers an electronic cam that locks the deadbolt. The handles come in a variety of sizes to fit various types of uPVC sliding door handles, and come in various attractive finishes that complement existing hardware. These handles are available on the internet or through a local locksmith. They are easy to install and come with clear instructions.

You will need to know your PZ cylinder's size to choose the correct replacement handle set. This is the distance in millimetres between the inside edge of the door frame and the center of the hole in the handle. It is also important to determine if the door is hook locks or a mortise lock. The easiest way to find the right handles after you have the measurements is to use the filter for brands on the website. This will narrow down the options and you can then choose the right size from the list.

A typical handle set includes the handle unit with two screws of various lengths, drill guides, and instructions for installation. The smarter models, such as the Igloohome Smart Mortise 2+ comes with a complete mortice lock with an integrated keypad. These are more complex models that are best for professional installers or highly skilled DIYers. Some handle sets include various accessories, like weather strips, which can be used to improve the appearance of the door.