How to Replace a kia ceed key fob Sportage Replacement Key

The key of many Kia models comes with an electronic keyless entry system built into. This key usually resembles an remote control, and can be exchanged with a new one from a Kia dealer or a locksmith.

Key fobs can fail to function due to a number of reasons, including an inactive battery, worn out buttons signal interference or water damage. Here are some suggestions on how you can get your Kia Sportage replacement key to function again.

How do you replace the remote key or the smart key?

The battery inside your Kia's smart key will eventually require to be replaced, whether it's a remote key or a push-to-start one, or a normal metal key that doesn't have an electronic transponder. This is particularly the case if your car shows a message that states the smart or remote keys are not powered by batteries.

Fortunately, it's quite simple to do. To replace the battery in the keyfob, remove your mechanical key from the slot at the back of the fob. Then, pull the cover open. Inside the key fob there will be tiny screws that hold the battery in the correct position. Take out the old battery by removing the screw with a small screwdriver. Then insert the new one and close the slit inside the key fob.

When the key fob is equipped with new batteries and you've tested it, press the lock and unlock buttons. If the doors unlock and lock exactly as you expect, then you're good to go! You can now utilize the kia rio 2015 key (you can try these out)'s hands-free lock/unlock feature whenever your fingers get chilly or you have to make errands in Brandon.

Note: Some key fobs may need to be programmed (transponder chips or smart key kia keys). This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your keys need to be reprogrammed, you must be aware of the number printed on the tag that identifies the key and keep it in a secure location.

How to replace the battery

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A low battery can also cause other issues, like the check engine light coming on or the engine not working properly. It is fairly easy to replace the key fob batteries with only two tools.

Before you begin the process ensure that your vehicle is turned off and all doors are shut. Find the small, metal or plastic piece on the bottom of the key fob. Then, jiggle it until the metal key pops out. The key can be put into the door's driver handle to unlock your car.

To replace the key fob battery, take off the cover at the rear and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery and then align the replacement kia car keys battery so that its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

After you have installed the new battery and turning the key fob off and on in the ignition until the door locks cycle. Then, test your Kia key fob to see whether it's functioning properly again.

How to replace the smart key?

Depending on the model of your Kia Sportage, you may have the standard key fob, or a smart key. The difference is that the smart key comes with tiny mechanical key blade in it, whereas the standard fob does not. Both kinds of key fobs contain a battery inside them which eventually needs to be replaced. This is an easy process that takes less than two minutes.

Be sure to switch off your Kia and sit on a flat or well-lit surface prior to when you begin. Also, remember that there are tiny components inside the fob that could fall out if not vigilant.

The small release button is located on the lower backside. It could be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been opened, take out the old battery. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. After you've finished, you should be able to lock, unlock and start your car with your key fob, even if the engine isn't running!

How to replace the mechanical key?

The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car by simply pressing the button. But like any device it may have issues from time to time. Luckily, there are methods to fix these issues and ensure that our key fobs are in good condition over the long haul.

One of the most common problems is a weak or dead battery. This can cause the device to stop working completely or to work intermittently. If this is the case, try replacing the battery with a new one.

If this doesn't solve the issue, try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. After opening, carefully remove the old battery and replace it with a brand new one.

Once the new battery is installed, close and unlock the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that can fit into the slot). Test the key fob and make sure it is working properly. Contact a dealer locksmith to fix the issue when the fob still is not working. To avoid lockouts in the future, ensure that you have an emergency key that will be able to work with all trunk and door cylinders.